Thin brick veneer in Mantua, OH
Thin Brick Veneer Supplier in Northeast Ohio
For homeowners and builders in Northeast Ohio weighing thin brick veneer for an accent wall, a fireplace surround or a lighter-weight exterior and who want to see it beside full brick before ordering.
Kelly Supply Co. sells thin brick veneer from its Mantua yard alongside full brick and manufactured stone, with take-home sample boards and delivery to 21 Northeast Ohio cities.
Call (330) 274-0260 during yard hours (Mon-Fri 7:00am-4:00pm) to reach the Mantua yard counter.

“Our contractor gave us info on Kelly Supply in Mantua, OH, to see if we could find something we liked for remodeling our wall behind our wood burner. The selection was incredible. The staff was knowledgeable & patient. They even made suggestions, but weren’t rude about it.”
Weight Per Square Foot: Thin Brick vs. Full Brick
Thin brick weighs less per square foot than full brick because the units are thinner, though exact weights vary by product line and by the adhesive and backing used. Most thin brick units are 1/2 to 1 inch thick and some reach 1 3/4 inches, compared with 3 5/8 inches for a modular full brick, according to the Brick Industry Association in Technical Note 28C and Technical Note 10.
Adhered thin brick can go where heavier anchored brick is hard to support, because thin brick systems impart less load to a building, as published by the same association. Thin brick vs. full brick compares the two in more detail, and full brick has its own hub.
Thin brick is $0.80-$1.80 per piece, and the price varies by brick choice and color.

Mortar/Adhesive vs. Mechanical Panel System
Mortar or adhesive installation and a mechanical panel system suit different walls, and the choice depends mostly on how flat and sound the wall is. The Brick Industry Association groups adhered thin brick into four methods in Technical Note 28C, shown in the table below.
| Method | How the brick is held | When it suits |
|---|---|---|
| Thick set | A mortar bond coat over a lath-reinforced scratch coat | Uneven walls, since the thicker coat absorbs irregularity |
| Thin set | Modified mortar or non-sagging adhesive in a thin coat, straight on the wall | Plumb, level walls, with cement backer board over studs outdoors |
| Modular panels | Brick adhered or secured to a panel that is fastened to the wall | Uneven or questionable surfaces, and installs that call for less skill |
| Prefabricated panels | Brick cast into precast or tilt-up concrete, or built on stud frames off-site | Large jobs built in a factory or on site |

Mortar and Adhesive Details
Mortar for thin brick should be ASTM C270 Type S, with or without a latex modifier, or an ANSI A118.4 modified mortar, as published by the Brick Industry Association in Technical Note 28C. Each brick should be pressed firmly into the bed and left alone once it starts to set, because improper setting is the most frequent cause of poor performance. Mortar installation belongs between 40°F and 90°F, and a masonry or concrete wall should cure 28 days before the first brick goes on, according to the same note. Joints are filled as the brick go up or afterward with a grout bag, and the courses should stay aligned while the bond coat is workable, according to the same note.

Movement Joints for Adhered Veneer
Movement joints in adhered veneer should be spaced no more than 18 ft apart in either direction and should enclose no more than 144 sq ft of veneer, as published by the Brick Industry Association in Technical Note 28C. Where a wall sits on masonry or concrete, the veneer joints should line up with the joints behind them.

Panels, Corners & Installation Accessories
Panels, corners and installation accessories decide how much a thin brick order covers and how the wall turns its corners. Modular panels typically cover 4 to 6 sq ft each, according to the Brick Industry Association, so a 100 sq ft wall takes roughly 17 to 25 panels before waste.
Corner units are formed in their final shape, cut from a single unit or mitered from several, and thin brick usually ships in boxes or strapped packages rather than stacked in cubes, according to the Brick Industry Association. Thin brick over a stud wall must sit at least 4 inches above grade, at least 2 inches above paving and at least 1/2 inch above exterior walking surfaces, as published by the association in Technical Note 28C.
Installation accessories for adhered veneer include a weep screed or flashing at least 0.019 inch thick with a 3 1/2-inch vertical flange, as published by the Brick Industry Association, and the thin brick veneer panels and corners page covers them in full.
Thin Brick Collections
Thin brick collections come in a wide variety of colors, textures and face dimensions, and for a wall faced with thin brick the Mantua yard lets you compare them against full brick and manufactured stone on sample boards you can take home.
Thin brick is made from clay that is extruded or molded at the final thickness, or from a thicker fired brick that is cut down, according to the Brick Industry Association. Exterior walls should use Grade Exterior thin brick, and interior walls generally use Grade Interior, as published by the association for ASTM C1088.

Why Buy Thin Brick Veneer From Kelly Supply Co.
Kelly Supply Co. is a family-owned Northeast Ohio supply yard that has sold masonry and stone from Mantua since 1997 and delivers across Northeast Ohio, with thin brick, full brick and manufactured stone in one place. A common myth says thin brick belongs only indoors, yet the standard has an Exterior grade made for outdoor walls.
Thin brick delivered nearby
- thin brick veneer in Chagrin Falls
- thin brick veneer in Hudson
- thin brick veneer in Aurora
- thin brick veneer in Solon
4.9 stars from 50 Google reviews
More in Thin Brick Veneer
Thin Brick Veneer Panels & Corners
Thin brick panels and corner pieces from the Mantua yard, with notes on panels, corners, installation accessories and take-home sample boards.
Frequently Asked Questions
How much does thin brick weigh compared to full brick?
Thin brick weighs less than full brick because the units are thinner, and the exact weight depends on the product line. The manufacturer's data sheet for the line you choose gives the figure.
Can thin brick go on an interior wall?
Thin brick suits interior walls as well as exterior ones, and Grade Interior units are generally used inside, according to the Brick Industry Association.
Do I use mortar or a mechanical panel system for thin brick?
Mortar or adhesive installation suits plumb, sound walls, while modular panels suit uneven or questionable surfaces, according to the Brick Industry Association's Technical Note 28C.
Which thin brick collections do you carry?
Thin brick collections at the yard change with inventory, so call the counter for the current lines.
Can I take a thin brick sample home?
Sample boards can go home with you from the Mantua yard. They are free to borrow, so bring them back when you are done.
How high above the ground should thin brick start on an exterior wall?
Exterior thin brick over stud walls should start at least 4 inches above grade, at least 2 inches above paving and at least 1/2 inch above exterior walking surfaces, as published by the Brick Industry Association in Technical Note 28C.
Choose, Match and Order from One Yard
Send the request form and the Mantua yard team follows up quickly during yard hours (Mon-Fri 7:00am-4:00pm).
